No Mercy Prostock Full Size Rules

Full Size Pro Stock

ALL RUST REPAIR MUST BE PRE-APPROVED OR MEET THE FOLLOWING REQUIREMENTS:

A MAXIMUM OF 18-20 GAUGE SHEET METAL OR OEM FLOOR MAY BE USED. MAY OVERLAP PAST RUSTED AREA 1-INCH ONLY. RUST REPAIR IS MEANT TO RESTORE CAR TO OEM, NOT STRENGTHEN. IF DEEMED EXCESSIVE IT WILL BE REMOVED.

GENERAL1. Any year car, no imperials.  PRE RAN CARS ARE PERMITTED HOWEVER THEY DO NOT RECEIVE ANY ADDITIONAL FIX IT PLATES NOR DO THEY GET ANY WIRE OR BANDING2. Any motor and transmission. Transmission cooler permitted in cockpit tightly secured.3. FULL CRADLES PERMITTED. SOLID MOTOR MOUNTS PERMITTED4. Transmission crossmember may be a max of 2″x 2″ 1/4″ tubing connected to frame by 1/4″ 4″x 6″ angle. You MAY NOT put the crossmember through the frame in any fashion.5. TRANSMISSION CROSSMEMBER MUST REMAIN A SINGLE BAR, NO GUSSETS, NO BELLY BARS OF GUSSETS. TRANSMISSION MAY HAVE STEEL BELL, STEEL TAIL SHAFT AND MAY HAVE
TRANSMISSION BRACE WITH SOLID TRANNY MOUNT CONNECTED TO
CROSSMEMBER ONLY.6. Slider driveshaft permitted7. ANY REAR, BRACING ALLOWED. NO BRACING MAY ATTACH TO BODY, FRAME OR
PACKAGE TRAY AND CANNOT STRENGTHEN CAR IN ANY WAY.  NO BUMP STOPS ON REAR8. Wheels and Tires9. Any ROUND tire may be doubled.10. Full wheel centers permitted, valve stem protectors allowed may not extend out past the wheel further than 1″. lip protectors, FULL beadlocks ARE PERMITTED, SOLID WHEELS PERMITTED11. Wheels may be spaced 1/2″ with additional center.


BUMPERS12. Both front and back bumpers may be any bumperMEETING THE SPECIFICATIONS STATED BELOW 13. No sharp edges, End caps permitted.14. May be seam welded15. HOMEMADE BUMPERS ARE PERMITTED BUT MUST MEET THE FOLLOWING
SPECIFICATIONS. MUST NOT EXCEED 8″X 8″. IF IT HAS A POINT THE POINT MAY NOT EXTEND MORE THAN 4″ FROM FLAT FRONT OF BUMPER. NEW….. FLAT BACK OF BUMPER TO FURTHERMOST POINT OF BUMPER CAN BE A MAX OF 12” MEANING 8” THICK BUMPER 4” POINT. IF THE BUMPER IS 6”X 6”OR LESS YOU STILL CANNOT EXCEED 4” POINT FROM FRONT FLAT OF BUMPER. NO EXEMPTIONS. POINT MUST TAPER OVER 32″. Bumpers cannot be sleeved around frame OR built around frame.  Bumper must be built from flush mounting SURFACE forward, not backward around frame.NO CHRYSLER POINTY BUMPERS OR POINTY REPLICAS THIS INCLUDES OEM LOADED POINTIES.  16. Bumper mounting: you may use a 2″X 2″ x 12″ x 3/8″ SQUARE TUBING OR A 4″ X 12″ 3/8″ thick plate on outside of frame Measurement for frame plate starts at the end of the frame. Plate can be on outside of frame, top ,bottom ,left or right. TEEPEE PLATES ARE PERMITTED, NO LOADING OF THE CONTOUR. 17. Measurement of plate from back of bumper with straight edge18. Bumpers may not be lower than 14″ or higher than 22″. Measurement taken from bottom of bumper. WAGONS, FRAME RAILS CANNOT BE LOWER THAN 12” NO MATTER POSITION OF REAR BUMPER. 

Suspension

03 AND NEWER

All 03 and newer cars must use a factory aluminum engine cradle and an OEM STYLE steering rack. Tie rods may be reinforced. These are the only restrictions for 03 and newer cars. All other rules apply. ( HD RACKS, TRUCK RACKS ARE APPROVED, BUT MUST BE DIRECT BOLT WITHOUT MODIFICATIONS.)

*If choosing to swap a 80s style body onto a 03 and newer frame, the car will be inspected as a 03 and newer and above rules will apply.

You may use an approved (by Deadman Derby) bolt in only piece for engine mounting purposes. Smith metal works style is approved. CATSKILL APPROVE. ( MUST BE A PART IN CIRCULATION IN MASS AVAILABILITY TO PUBLIC) All others must be or approved. No welding piece in.1. Cars do not have to bounce2. Rear suspension may be 1″ all thread. 3” MAX WASHERS3. Coils may be welded to the rear and banded to the body in one spot.4. NO LEAF SPRING CONVERSIONS5. NO AFTERMARKET A ARMS6. Front suspension may be solid. Upper A arm may be contoured to frame and may be welded either with a single pass 4″ bead 1 per side or use a 4″ x 4″ max A ARM to frame on each side.(2 per A arm)7. A Arms may be swapped OEM to OEM. Ball joints MAY BE AFTERMARKET AND may be welded in. Spindles OEM to OEM, NO aftermarket spindles8. NO MOVING OF A ARM FRAME BRACKETS. MUST ME IN STOCK CONFIGURATION AND PLACEMENT.  9. Front shock can be 1″ all thread. 3” MAX WASHERS10. Sway bar must be bolted to the lower control arm and may be attached to the frame with a piece of 2×2 tubing no more than 4” long tubing may be welded to frame, ½ BEAD OF WELD MAX11. No chains on suspension anywhere12. Watts link kits are permitted. If using a watts link aftermarket or homemade it must bolt to the package tray utilizing only 1/2″ maximum bolts. You MAY NOT, bolt through the package tray to the body. NO WELDING TO PACKAGE TRAY. Watts link uppers must be two separate pieces. Lowers may be a max of 2”x3”x 1/4″ cut for desired pinion angle and mounted in one fashion. A bracket on the inside of the frame may be welded but lower trailing arm must bolt to that bracket. LOWER trailing arm CANNOT BE WELDED IN ANY FASHION.WATTS LINK KIT CAN ONLY BE BOLTED TO PACKAGE TRAY NO WELDING (IMPACT KITS, TOAST KITS ARE ARRPOVED) 13. Leaf Sprung Wagons and Sedans: No aftermarket leaf packs, no flat stacking or flip flopping leafs. No springs on top of main spring. 9 leafs maximum, 3/8” maximum thickness, 2″ stair step AND STAGGER, 4 clamps per LEAF PACK. Clamps maximum of 1/4” thickness 2″ max width and bolted with 3/8″ bolts. LEAF SPRINGS CANNOT BE ON TOP OF REAR END IN ANY FASHION.  

Steering1. Steering boxes must be mounted at factory location,however you may utilize an aftermarket adapter plate if you prefer to change steering box OEM to OEM between manufactures. ADAPTER CANNOT BE USED TO STRENGTHEN FRAME. 2. TIE RODS MAY BE REINFORCED. AFTERMARKET PERMITTED. HEIM JOINTS
PERMITTED. 03 AND NEWER MUST UTILIZE OEM STEERING RACK3. Aftermarket steering columns permitted.4. Center link must remain factory5. NO HYDRAULIC STEERING

FRAME1. SEAM WELDING FIREWALL FORWARD IS PERMITTED. TOP SEAM ONLY. NO OTHER SEAMS MAY BE
WELDED2. TILTING PERMITTED. YOU MAY TILT IN ONE SPOT PER RAIL ONLY NO EXCEPTIONS. ½” BEAD OF WELD WHEN REWELDING TILTED AREA. NO ADDING METAL TO TILT. 3. NO PLATING, NO STUFFING OR PINNING an ultrasound will be utilized to measure
frame thickness4. Rear frame may be dimpled or cut for rolling. ALL CARS….REAR FRAME RAILS MUST BE AT MINIMUM 12” FROM GROUND. 5. You may shorten the front frame, FRAME MUST REMAIN 20” FROM FRONT OF COIL POCKET ON BOTTOM OF FRAME FORWARD, TAKEMEASUREMENT WITH TAPE MEASURE HOOKED IN FRONT MOST PART OF COIL POCKET. ON 03 AND NEWER MEASUREMENT WILL BE FROM THE FRONT CRADLE MOUNTING BOLT FORWARD ON TOP OF FRAME6. A 22″ X 6″ X 3/8″ MAX HUMP PLATE IS PERMITTED ON THE OUTSIDE OF FRAME CLOSEST TO WHEEL. Hump plates must be between the body mount in front of the arch and the body mount behind the arch. You choose the exact location  Leaf sprung sedans and wagons get an 11’ x 6” X 3/8” HUMP PLATE BUT IT MUST BE CENTERED IN HUMP. METRIC GMS GET A30” HUMP PLATE……7. No painting or undercoating on frames. No putty.8. You may swap frames but the car will be inspected based on make model and year of frame. 9. All body mounts may be changed to 5/8″ BOLTS. BODY BOLTS MAY ONLY PASS THROUGH THE TOP OF FRAME AND BODY. MAX OF 3” WASHERS.10. A 1″ MINIMUM space must be maintained at all times. This may be achieved utilizing any of the
following: solid, OEM , Hockey pucks11. Boxes are limited to 4″ space. Core supports a MAX space of 8″. Core support spacers only, may be weldedTO THE FRAME TOP OR SIDE BUT MUST REMAIN STRAIGHT UP AN DOWN SPACER NO BIGGER THAN 2” BOX TUBING.12. IF A CAR IS SHORTENED TO 20” AND THECORE SUPPORT PEDASTAL NEEDS REPOSITIONED… HERE IS THE ONLY WAY IT CAN BE.  CUT THE FACTORY PEDASTAL OFF, WELD YOU 2”X2” MAX CORE SUPPORT SPACER TO THE SIDE OF THE FRAME DIRECTLY BEHIND THE BUMPER.  THE CORE SUPPORT SPLACER WILL STILL BE LIMITED TO A MAX OF 8” TALL.  13. Rust repair is limited, ALL MUST BE PRE-APPROVED.
BODY14. The Driver’s door AND FRONT PASSENGER DOOR may be welded solid and you may have full door skin 1/4″ max overlapping no more than 6” on either side of door. DOOR SKIN NOT PERMITTED ON REAR DOORS No protruding metal or rails outside drivers door.15. All other door seams may be welded in a 5″ on 5″ off fashion. Outside seem only16. Trunk 5″ on 5″ off17. Trunks may be dished or canoed. A 2″ space must remain from trunk floor to trunk lid.
Measurement will be taken from lowest point of lid and highest point of trunk if beat up.
YOU MAY ONLY USE AN OEM TRUNK LID NO HOODS. SPEAKER DECK MAY BE REMOVED, ON ALL CARS YOU MAY ADD 2 PIECES OF 1” ALL THREAD IN THE TRUNK WITH NO MORE THAN 4” WELDED TO THE FRAME AND NO MORE THAN 3 NUTS ON EACH PIECE NO BIGGER THAN A 3”X 3” WASHER WELDED TO DECKLID18. Mandatory: 2 10″ holes one per side of trunk lid for inspection . Holes may be bolted with 3/8″ bolts in 10 spots.19. Trunk may be tucked20. Hood: May be secured in 6 Spots. Can be chained or bolted. If bolted you may only do so in the following fashion: Angle 2″ x 2″ maximum of 1/2″ bolts.1 BOLT PER SPOT. NO NINE WIRING HOODS. FRONT CORE SUPPORT MAY BE USED AS 2 SPOTS UP TO 1″ ALL THREAD. ALL THREAD MAY NOT RUN THROUGH FRAME RAIL. MAX OF 3″ WASHERS.21. A minimum of 2 12″ holes must be cut. Holes may be bolted with a maximum of 3/8″ bolts and a max total of 16.22. Fenders may be cut and rolled for clearance and welded back together or bolted a max of 8 times with 3/8″ max bolts or 8-1” welds23. All fenders and body lines may be creased both horizontal and vertical. Be creative.
However, side rear fenders must remain upright, not beat down.24. Expanded metal Permitted at core support for radiator protection ¼” THICKNESS MAX. Partial or full radiator protectors ARE PERMITTED. Water only in the Radiator.25. No wedging26. Speaker Deck may be removed or beat down. No rewelding of speaker deck in new
locations.27. Roof sign Mandatory for Identification28. no additional nine wire, banding, chain or cord allowed other than specified
CAGE29. Four point “floating cage” Dash bar, rear seat bar two side rails. In addition to side rails a center bar from rear bar to dash bar. ALL CAGE MUST REMAIN INSIDE COCKPIT30. Dash bar must remain 5″ from the firewall. Side bars cannot extend beyond 10” OF FRONT DOOR SEAM NOTHING OTHER THAN SIDE BARS MAY BE PAST THE DASH BAR31. Cage may be gusseted at corners.32. ON DRIVERS SIDE AND PASSENGERS SIDE… 2 ON EACH SIDE BETWEEN DASH BAR AND NO FARTHER BACK THAN
REAR SEAT BAR FOR DRIVER PROTECTION OR EQUIPMENT MOUNTED ON FLOOR PROTECTION. THESE BARS MUST BE PLACED BEHIND DASH BAR AND MAY BE WELDED TO THE FRAME. DOWN LEGS CAN BE NO BIGGER THAN 2”X2” TUBING33. A gas tank protector is permitted. No Wider than 32″. Gas tank protectors may butt up against the package tray and MAY HAVE TWO ½” BOLTS THROUGH THE PACKING TRAY34. Gas tank protectors may have two diagonal rails to halo or rear seat bar BELOW WINDOW.35. Halo bars recommended. Halo may be bolted to the roof.36. From the halo bar a front bar may be used and can connect to the dash bar and welded . Rear window bar. Limit of 2×2 1/4″ from halo to speaker deck. a 5”X5″ plate is permitted at the bottom of the rear bar and may overlap and be welded to the trunk lid. This plate must coincide with the 5 on 5 off rule.37. MAXIMUM SIZE OF CAGE MATERIAL IS 6” MATERIAL
NO PASSENGERS38. NO SHORTENING OF BODY IN ANY FASHION, NO WRAPPING FENDERS, they must remain upright and parallel. Body mounts must be utilized in factory locations. 3 inch maximum washers. Body bolts may only pass through the top of the frame39. ABSOLUTELY NO PLASTIC FUEL CELLS> MUST BE AFTERMARKET PRESSURE TESTED FUEL CELL• For your convenience and ours, please remain within rules. These rules are set to allow for some creativity but not to be abused. If it does not say you can do it. It is NOT PERMITTED.If you have questions or concernsplease call first. 2 attempts only
drivers. All cars will be on a level playing field. Good luck! 


Jacob Gilliam 614-315-7468. Please do not call or text after 9 pm eastern time.

DURING BUSINESS HOURS 9-5 JACOB IS BEST AVAILABLE THROUGH TEXT AND AFTER FIVE VIA PHONE CALL.  FOR MULTIPLE QUESTIONS PLEASE ALWAYS CALL.  

%d bloggers like this:
search previous next tag category expand menu location phone mail time cart zoom edit close