2 Man Teams
Just like in a Tag Team Match only one car per team may participate at a time.
All cars will start in designated safe area at either end of the arena. At the drop of the green one car from each team will enter the live part of the arena.
At any time you may chose to tag in your partner. To tag your partner in, you must make contact with their car in the safe area. All other contact from other competitors in this area is prohibited and will not be tolerated.
If your car is car is unable to continue and is eliminated this automatically tags your partner in.
Match will be ran down to last car to make a competitive hit.
$2,000 Winner take all
The rules below are not guidelines, this is a street stock event meaning that all unspecified areas of car building below are required to remain OEM as intended from manufacture in regards to material, placement and structural integrity of both frame/unibody and body panels.
ANY BODY SEAM WELDING( outside of what is clearly outline in rules) WILL BE AN AUTOMATIC LOAD, YOU WILL NOT BE GIVEN A CHANCE TO FIX THIS AT THE DERBY.
ANY FRAME SEAM WELDING OUTSIDE OF WHAT IS OUTLINED IN THESE RULES WILL AUTOMATICALLY GET YOU LOADED
ANY FRAME PLATING OUTSIDE OF WHAT IS STATED IN RULES WILL BE AN AUTOMATIC LOAD
ALLRUST REPAIR MUST BE PRE-APPROVED OR MEET THE FOLLOWING REQUIREMENTS:
A MAXIMUM OF 18-20 GAUGE SHEET METAL OR OEM FLOOR MAY BE USED. MAY OVERLAP PAST RUSTED AREA 1-INCH ONLY. RUST REPAIR IS MEANT TO RESTORE CAR TO OEM, NOT STRENGTHEN. IF DEEMED EXCESSIVE IT WILL BE REMOVED.
No fix it plates
1.This class is for FRONT WHEEL DRIVE CARS ONLY maximum of 113” wheelbase
2.Cars must remain stock unless specified in these rules
3.Aside from dash and front seats, interior must be stripped entirely. MUST remove air bags and the charges. Do not just set them off remove them.
4. does not have to key start but you must run a factory steering column and shaft
5. All doors may be wired or chained 8 spots per door max. IF WIRING YOU MAY WELD 1” HOLED WASHERS FOR WIRE TO RUN THROUGH
6.Deck lids may be wired or chained in 8 spots max. IF WIRING YOU MAY WELD 1” HOLED WASHERS FOR WIRE TO RUN THROUGH
7.Hood may be wired in 8 spots max. IF WIRING YOU MAY WELD 1” HOLED WASHERS FOR WIRE TO RUN THROUGH
8.No creasing or wedging on rear of car
9.Bumpers are to be stock. You may choose to run 98 and newer front bumpers which are the same as a lumina bumper.
10.Bumpers may be welded all the way around at the attachment point you may not add shocks to a car that doesn’t come factory with bumper shocks. All cars that came with a bumper shock must keep the factory shock in the factory manner.
Front- 2 strands of double braided nine wire may go around bumper one time and around core support. ONE LOOP. No criss crossing of strands. Cannot go through the hood.
Rear- 2 strands of double braided nine wire may go around rear bumper and then through the trunk lid. Where it goes through the trunk lid can be no father forward than half the of trunk lid. No criss crossing strands
11.You may have 2 spots of 9 wire in the windshield area
12.Battery may be moved to inside of car but does not have to be. It is STRONGLY recommended that if battery is under the hood, it must be spray foamed in place. If moved to the cockpit of car, no wood battery boxes, must be secured tight and a steel battery box is recommended.
13.If gas tank is in front of rear axle, it is recommended that it be left in the factory position under the car
14.If gas tank is moved from under the car it must be replaced with a METAL tank in the rear seat/rear floor board area. Tank must be mounted securely to floor. You may not use ratchet straps to secure tank. You may NOT mount a factory tank inside the car. Any fuel system we feel is unsafe will not be allowed to run.
15.Tires may be doubled and tubed any tire allowed no bead locks or rim protectors of any kind. Nothing may be welded to wheel
16. You may run a seat bar. No larger than 4″x4″, from B pillar to B pillar. If needed to accommodate drivers seat, you may use one 8″x12″1/4″ plate welded to each B pillar to weld bar to, so that seat may be slide back.
17. No aftermarket shifters.
18. wiring harnesses are permitted. you may hard wire the electric fans to a switch
19. headers are permitted
CARS MUST REMAIN STOCK UNLESS STATED IN THESE RULES
ALL JUDGES DECISIONS ARE FINAL
Any Questions please call Ryan Ruhe at (937)-408-7269